CLEMENTS 107di
Greg Weaver, SoundStage! May 1998
(www.soundstage.com)

I love Halloween. I have since my childhood. To me, October 31st heralds the official arrival of fall, long my favorite of all the seasons. The sensory spectacle provided by the annual seasonal transformation in the northeastern United States starting in early October is truly a multi-faceted experience not to be missed; the changing of the leaves, the vivid, warm colors, the crisp and inviting smells, the carnival of sounds, and don’t forget football. What’s not to love? And what a holiday this magical season brings. Anything can happen on Halloween. Anyone can show up at your door and challenge you with that ageless phrase, "Trick or treat?" Well, imagine the look on my face last Halloween when Phil Clements, maestro at Clements Loudspeakers, walked through my door with a quizzical smile on his face looking for me.

What a conversation we had. I was surprised to learn that back in the late ‘70s, Clements had been the designer of a little speaker called the Phase Research Model R. He was equally surprised to hear me rattle off a complete description of the thing and its price. Yes, I clearly remembered it as a speaker that performed well above its price point. I still have one of the sales brochures in my files. After about an hour’s discussion, I had a brief chance to hear a pair of bookshelf speakers, the Clements 107di. With barely a 15-minute audition I was convinced that if these speakers sold for $600 they would be a bargain. I had deliberately guessed a bit low because I expected I was being set up. When Phil told me that these babies went for under $400 a pair, you could have just about knocked me over. I started the arrangements for a formal review right then and there.

In mid February, with all the hubbub of the Winter CES behind, products once again began showing up at Chez Weaver. Among the early arrivals were these little guys from Clements. The 107di (the "d" stands for dynamic and the "i" stands for image) is the middle sibling in the di series, with two little brothers each above and below 107di’s price point. Nicely finished yet unassuming black boxes, 16.5" tall by 9.5" wide and 11" deep, they were fitted with a pair of typical plastic-nut five-way binding posts. The large 3" diameter port was near the bottom rear of the speaker. Removing the grille revealed the .75" polycarbonate ferrofluid-cooled tweeter and the 6.5" poly-laminate mid-woofer, both of which appear to be of Audax/Polydax lineage. Hmmm. Fairly unassuming again. The grille was attached with four ball-and-socket snaps and was covered with a fairly open-weave black cloth. Although attractive enough in fit and finish for their $390 retail price, with the exception of the ten-year warranty, the speakers appeared to be pretty average.

Tricks

Over a decade ago, Phil Clements read the results of a listening test that changed the way he thought about speaker design. In the study, groups of people were subjected to listening to the same speaker complement with crossovers of varying designs. The speaker’s cabinet, woofer, tweeter and crossover frequency remained identical, but the slope, or rate, of the crossover point was modified. The speakers were auditioned with 6dB-, 12dB-, 18dB- and 24dB-per-octave filter networks. The results of the test were quite interesting. Unanimously, the panel preferred the first-order 6dB-per-octave crossover, also known as an open-slope design, both in terms of providing a more "natural" sound and a more realistic presentation of the soundstage. The panel then chose, in order of sonic preference, the 18dB, then the 24dB and finally the 12dB crossovers. I’m not about to go into all the reasons why these subjective results make sense technically. More interesting is the story of how this one man chose to utilize the results to develop a high-quality yet affordable line of loudspeakers.

The desire to use the 6dB network was obvious given its inherent purity and the overwhelming preference among listeners. It is the only filter slope that electrically adds back to, or very near to, "zero" phase shift through the crossover-frequency region without the use of rigorous and destructive compensation. All the other networks impose easily measurable, and as easily audible, amounts of electrical phase shift in comparison to the input signal. Even with careful compensation it is next to impossible to retrieve the high degree of integrity inherent with the single-pole filter.

Even though the steep-slope filters tend to corrupt the original input signal by the huge amounts of electrical phase shift they impose, they do have several highly sought-after design benefits. One of the most important of these is the preservation of bandwidth power. Since the steeper-slope filters obviously mean a steeper roll off, certainly much faster than the open-slope design, they provide, with all else being equal, greater overall speaker sensitivity. The extended, slowly reducing slope of single-pole filters is typically not a good way to produce a terribly efficient speaker. Check the published sensitivities of other well-known champions of the open-slope crossover design, companies like Celestion, Thiel, Vandersteen, Sonus Faber, and Dunlavy. Their speakers are not known for their efficiency.

Other advantages derived from steep-slope filters include greater driver protection and increased detail, both of which are obviously highly desirable. Unfortunately, to gain these desirable results at the price point of the 107di, one typically has to impose high amounts of electrical phase shift. That is exactly what Clements wanted to avoid because it meant compromising the one thing that was paramount in his design goal, signal integrity.

So how does one maintain the integrity achievable with a first-order design and still find a way to apply the benefits desirable from the higher-order networks, and do it on a budget if possible? Based on the results of that earlier listening test, Phil decided he would like to see what he could do to impose no more than a single-pole filter electrically. Yet for the sake of greater resolution and dependability, he wanted to try to obtain final acoustical slopes of 18dB per octave, since that was the slope with the second-highest approval rating in the survey. If he could develop a way of combining the single-pole electrical slope for signal integrity along with the power preservation, better dynamics, higher protection capability, greater detail and cleanliness of the steeper slopes, he felt he would have a winner.

If only 6dB were available from the electrical filter, a single inductor in this case, then what else could be applied to help add another 12dB and achieve the desired 18dB total? Well, all drivers, at the end of their bandwidths, have an inherent roll-off determined by things like their size, mass, weight, materials, magnetic intensity, etc. Knowing all that, and paying great attention to detail, you could design a driver to roll-off at specific rates. So some, if not all, of the additional slope rate might be achieved by paying close attention to component driver design.

This control has to be achieved at a specific rate within a limited acceptable frequency range. If the bandwidth of the driver extends too far in frequency response, then once again, steep electrical slopes would be required to properly knock out unwanted bandwidth. Although many factors must be taken into account, a desired roll-off characteristic can be engineered into a driver. Difficult as this is for one driver, this process becomes exceedingly arduous to control with the addition of multiple drivers, as would be necessary in a two- or three-way design. All the other required design parameters of each different driver to be incorporated into the final design will combine, contribute, and limit certain ways to gain consistent slope rates from the components themselves. Certain slopes at or within the proper bandwidths could be counted on, but not always at the same rate. Now what?

This meant that yet a third element needed to be introduced, one that would get the desired overall 18dB-per-octave acoustic slopes with different components of varying characteristics, and do so consistently. This third factor had to be the most variable when applied. The perfect component was an impedance compensation network, which ideally every speaker should utilize anyway. Since all voice coil type drivers exhibit rising impedance caused by the voice coils inductive reactance, one highly desirable purpose of such networks, called "Zobels," is to equalize that rising impedance. This allows for the presentation of a much more friendly and consistent load to the amplifier. Add in that one of its other benefits is its ability to knock out frequency response at different points, variably in slope no less, and you’ve got the final ingredient in Phil Clements’ super crossover recipe.

Treats

I don’t believe in critical evaluation of any product right out of the box, and the 107di was no exception. When you audition these guys for yourself, make sure the pair you hear has been well run in. Some of the "edge" begins to disappear after ten hours or so, and at 60 or more hours of play, the speakers begin to show off their stuff. My first audition of these little guys was with my reference rig, and in this system even the interconnects and speaker cables cost more than the speakers under evaluation here. But what did they truly have to say for themselves? This was one sure way to find out.

One of my long-time standard evaluation records (that’s right, I said record) is my Mobile Fidelity half-speed copy of Supertramp’s Crime of the Century (Mobile Fidelity 1-005). There is a solo harp (that’s a harmonica to those of you who find yourselves blues challenged) in the opening cut playing very deeply at center stage. As the tune progresses, there are numerous voices of children scattered through the very back of the stage covering nearly its entire width. There are a whole host of other things stage left and right at varying depths. The harp was recreated solidly where it belonged in the stage and had a wonderful warmth about it. The voices were placed deeply and accurately throughout the stage, as were the rest of the instruments in this fairly challenging soundstage. Hmmm. These diminutive speakers were beginning to hint at being considerably better than average.

I was justly amazed with what these little guys did with any Q-Sound effects they were supplied. Every cue was perfectly located and quite tonally correct. Moving to "Welcome to the Machine" from Pink Floyd’s Wish You Were Here (Columbia Half Speed HC33453), the weight of the "machine" was pretty convincingly portrayed, if just a bit fat in nature. The ports, a whopping 3" in diameter, start to generate a real breeze around 60Hz and continued to exhibit usable output as low as about 30Hz, though down considerably in terms of sensitivity. And even thought the little ports were moving air at a rate that would be impressive in a small cooling fan, there was no chuff or port noise whatsoever.

The piano from the "Fantaisie - Impromptu" on Horowitz: The Last Recording (Sony SK 45818), though presented slightly smaller and more constricted in three-dimensional space, was still nicely conveyed in terms of the warmth, body and the magic of the performance. The timbre and luster of the piano, which is one of the better attempts on CD in my opinion, was presented accurately and with the kind of "involvement" associated with the much higher-priced spreads.

With the Seven Years In Tibet soundtrack (Sony SK 60271), the 107di’s recreated a nice impression of the heft of the lowest frequencies even though, being bookshelf speakers, they could not truly excavate the nethermost depths of the recording. The glimpse into the soundstage was just a bit shallower than I would like, with a bit more forward presentation than is realistic, but devastatingly insightful. Yo-Yo Ma’s cello is surprisingly detailed as are the rest of the midrange voices presented here. There is a realistic interpretation of the upper frequencies with just a hint of hardness in the loftiest registers that is almost venial given the ease and vitality imparted through the midrange.

OK, but what about the real world? How likely is it that this speaker would be used in a $20,000-plus system? Yeah, that’s what I thought you’d say. Dropping the speakers into my office system (consisting of a 50Wpc receiver, a portable CD player, and regular old interconnects and loudspeaker cables hitching everything together) seemed to be the logical next step. The results were unreal. Could it be that these speakers sounded even more impressive in this more humble and likely application? Yup. Not that they sounded better here than they had in my reference room, but they sounded as good. They retained all of their attributes, while their shortcomings seemed diminished. I had expected them to shrink when placed in the lesser system. If anything, the level of accomplishment actually grew. They took the system to new heights. Again, the ppreciable tonal balance, excellent staging and adroit bass heft delighted me with their unwavering presence.

These little speakers are very engaging, rendered a startling glimpse into the soundstage, offered worthy mid-bass performance and had a convincingly neutral tonal balance, even if tilted a bit toward the darker side of neutral. My only complaints were pretty much what you would expect in a speaker selling for twice, maybe even three times, the price of the 107di. From the lower mids up they are a bit on the opaque side of transparency. There is a bit of hardness starting in the upper midrange and going on up, while the midbass is a tad loose and exaggerated. Damnation you say? Far from it. Remember the meager list price. The take

You know, I’ve been around this game for about a quarter of a century and I cannot name another loudspeaker manufacturer who puts this much thought and technology into a speaker at this price point. Once you crack the $1000 price range, yeah, maybe you expect to get this kind of design and execution. But at under $400, the Clements 107di is an unheard-of and unbelievable achievement.

While it is true that these little guys suffer from the same types of maladies as any inexpensive bookshelf speaker, they do so to a significantly lesser degree than anyone would have any right to expect given their extremely modest selling price. With the Clements 107di, your $400 buys you an extremely well-conceived and well-executed product with tremendous clarity, focus, openness and tonal truth. If your speaker budget is $650 or less, put these $390 standouts at the top of your short list.

CLEMENTS 206di
Lonnie Brownell, Stereophile, April 1997

"One thing you can count on at a show like the WCES is that there will be speakers on display. Lots of speakers. Every room had at least two, and I'm here to tell you about some of the new and interesting ones with real-world price tags.

One speaker with an embarrassingly high value:price ratio was the 206di ($750) from CLEMENTS, part of their 'dynamic image' series. This large, two-way speaker provided a full if somewhat polite sound that had me thinking it must go for bigger bucks."

CLEMENTS 206di
Bound for Sound, April 1997

"CLEMENTS 2-way, 3-driver, floorstanding loudspeaker for $750: People were saying that I had to hear the speaker from CLEMENTS before the show was over. And as is usually the case, the word on the streets was right. The speaker is around 40" tall, about 8" wide and 10" deep (approximations). It has two 6.5" woofers and a 1" soft dome tweeter and was being driven by PS Audio electronics. For the asking price of $750, the CLEMENTS, was a sonic standout. Having the room-filling capabilities of speakers much more expensive, the CLEMENTS had the tonal trueness of speakers in the 2-3 thousand dollar range. For that reason alone, people were guessing the price to be well above a thousand dollars, only to have their guesstimates dashed out when the true retail price was revealed. I admit that I was impressed too by what I heard. One negative might have been the upper bass that lacked some control, but when factored into the entire equation, that seemed pretty trivial. A must audition for the budget audiophile."

CLEMENTS 206di
Chuck Bruce, The AAS Journal, April 1997

"Another top performer at a value was seen and heard from the new CLEMENTS 206, vented two-way floor-standing dynamic loudspeaker with 1" fabric dome tweeter and a pair of 6" poly drivers with impedance compensation. The designer stating an easy to drive 90db sensitivity, stable compensated 6-ohm impedance and solid 35Hz bass response at $750 per pair! This ensemble represented another one of the best buys at the show, with many attendees making second visits to verify what they had heard at this price point from a dedicated mid-west designer. Lateral, front and rear imaging and sound staging was first rate as was off axis listening, with excellent perceived time coherence and driver blending due to a stated carefully engineered premium parts crossover. Use of attractive black oak vinyl over 3/4" and 5/8" MDF instead of rare wood cabinetry keeps costs down. Effectively sourced by PS Audio gear, 70 pre-amp, Lambda CD drive and 200 delta power amp, this is an ensemble to watch. A somewhat larger and higher priced model 306 features a pair of 8" double-active mid-woofers that also looks like a serious challenger to the high-end. Quite Amazing.

Before I leave this section, I must add the Audiostatic, Threshold, PSAudio, SpeakerArt, Presence Audio and CLEMENTS rooms merited more than one visit to see if I had heard it right the first time. Sure 'nuff, follow-up visits confirmed these impressions. And the sound was even better after a couple of days of warm-up and acclimating the loudspeakers to the rooms."

CLEMENTS 206di
Mike Masztal, SoundStage!
(www.soundstage.com)

"If you've been consistently reading  SoundStage! and other audiophile journals,  you've undoubtedly noticed that the price tag  on certain pieces of equipment have been escalating.  The AudioNote Gaku-on sells for $245,00/pr., and an increasing number of speakers are selling in the upper five-figure range.  The good news is while the price envelope seems to be expanding, the performance envelope, in my opinion, is shrinking.   In last month's issue, I reviewed the Wisdom Audio Adrenaline.  It was an incredible speaker and for $25,000., it should be.  But I can't afford them.  My whole system costs less than one-half  their price.   How about something for the other 99% of  burgeoning audiophiles who have those pesty other obligations like food, rent, utilities and the kids shoes. Well, if value is an important consideration in your hi-fi budget, read on.

During a recent visit to my favorite audio shop, Audio Essence, Jim Kean, the owner, said I had to listen to the new Clements speakers he had.  The Clements had received some rave reviews from some Atlanta Audio Society friends who attended '97 CES, so I was anxious to hear them.  After an hour or so of excellent sound, I thought SoundStage needs  to review these.   All it took was a phone call to Phil Clements and the $850. Clements 206di were in my car heading back to Atlanta.

My System:
Source:  CAL Delta transport, Alpha DAC retubed with Brimar CV4004 (my thanks to Kevin Deal for his assistance);   Pre-amp: Aranov LS-9000;  Amps:  Aranov LS-9100 monoblocks;   Speakers:  JM Labs Daline 3.1;  Interconnects:  JPS Labs  Superconductor;   Speaker wire:  Nordost  Super Flatline;  Power cables:  JPS Labs and Camelot  Sir Bors.  Listening room is 12' by 18' by 8.5', complimented by Corner Tunes and home brewed room tunes. 

The Design:
Phil  Clements, best known as the designer of the Clements RT-7 ribbon/dynamic hybrid  from a few years back, has launched a new line of affordable stereo and home theater speakers.   Phil has incorporated a number of  designs which account for the excellent performance of  his new speaker line. One unique and proprietary design parameter involves both the drivers and the crossover engineering.  A 6 db/octave minimum phase filter network and impedance compensation network are employed to minimize or eliminate electrical phase shift through the crossover region.  However, it is combined with specially designed woofers, such that when combined with the above described filter network, actual 18 db/octave acoustic filter slopes are achieved.  The advantages of the steeper slopes are increased sensitivity, greater component power protection and increased overall sound cleanliness and detail.   The crossovers are hand built and hard wired using mylar and polypropylene capacitors in a bypass configuration.  No printed circuit boards are used. These features are usually found on speakers costing many times that of the Clements, such as Sonus Faber, Theil, Dunlevy and Vandersteen.

Typical impedance curves for all Clements models from around 80 Hz to 20kHz range from +/- 1/4 ohm to no more than +/- 5 ohms, as is the 206di.   This represents a very stable load to any amplifier.   For those with moderately priced amplifiers/receivers, the 206di should be an excellent match as the 206di won't strain the amp's power supply.   I should also note that the entire line of Clements speakers have essentially the same design characteristics and are similarily voiced. An important consideration for those assembling a stereo/home theater system.

The 206di measures  38" x  9.5" x 11" D and weigh 40 lbs each.   Driver configuration is a 2 way design consisting of  a pair of 6" woofers and a 1" tweeter in a D'Appolito arrangement with a rear facing 4" port.   One pair of 5 way binding posts are mounted about 18  inches from the bottom.   Phil Clements also includes a heavy duty set of spikes with the speakers to allow for stable coupling to the floor.

Set-up:
Since these speakers were demos, no break-in period was necessary.   Setting the 206s up in the same place as my Dalines, i.e., 24" from the rear wall and 33" from the side walls overloaded the room and produced a thick atonal bass and mid-bass that blurred the critical midrange.   Moving them out  34"  from the rear wall cleared up that problem.  With the speakers pointing straight ahead, there was a sight gap in the center soundstage.  Positioning with a very slight toe-in allowed the middle soundstage to fill nicely.  I preferred listening with the grills off.

The Sound:
I first listened to my favorite CD, Ottmar Liebert's "VIVA!".   63 min, 45 secs later, I was quite enamoured with the sound.   Enough fun stuff.  It was time for the Parris Island* discs.   Steve Tibbets "The Fall of Us All"  (ECM 1527), has a percussion section that would make Santana proud.   There are also some hard transients on that CD that not only test an amplifier's guts, but also the ability of a speaker demonstrate their dynamics.  The 206s handled them very well and they can also play very quiet passages while maintaining low level detail.   Their ability to reproduce soundstage is very good.   John McLaughlin's "Live at the Royal Festival Hall" (JMT 834 436-2), is an excellent example of what "ambience" and "soundstage" is supposed to be.  Using  Strunz and Farah's "Primal Magic" ( Mesa R2 79023), the Clements showed their quickness by accurately playing the 32d note runs without blurring the sound.  Orchestral music does well without the various instruments blending into an amorphous sound.  Spatial relationships were stable as evidenced on track 8, "Running From Mercy" on Ricki Lee Jones "Traffic From Paradise" (CD Geffen 24602).

Piano and vocals are also beautifully reproduced.  Sarah McLachlan sounded like she was in my room on cut 12' (a vocal/piano reprise of  "Possession") of her "Fumbling Toward Ecstasy"  (CD Arista 18725-2).   I found no sibilance on vocals of artists like Emmy Lou Harris or Loreen McKennit.   The Clements also handle good old rock and roll with the punch we've all come to appreciate. "I'm a Real Man" from Robben Ford and the Blue Line (GRP STD-11020)  never sounded so good.   Bass response was very good with a tonal correctness to the sound.  Compared to my Dalines, the Clements 206di  have the characteristic "box speaker" sound, but no more than the other 99.99% of box speakers out there.  They are also not quite as transparent as the Dalines, but are a lot more authoritative in the low end.  All in all, the Clements are pretty much on par with my Dalines.  The difference being the Daline's transparency and lack of 'boxiness' versus the Clements' better low end.

Impressions:
My only concern with these speakers is their price. At $850., they're TOO CHEAP!!!   The Clements 206di can accomplish 95% of what my Dalines can (plus more bass) at roughly half the cost!   Quite an accomplishment considering the Daline 3.1, in my opinion,  perform far beyond what one might expect from their $1400. price tag.   Unfortunately, there are a group of audiophiles who believe there is an absolute correlation between price and performance and probably won't give the Clements a listen.     While there is some truth to that belief, you cannot quantify performance by the number of digits on the price tag.   I've learned that the hard way.

In summary, the Clements 206di is a steal at it's price and anyone with a speaker budget of  up to $2500. would do himself a disservice by not auditioning the 206di.  The potential savings can be applied toward  a new power cord for your CD player, better interconnects, etc.   These upgrades, in my opinion, will offer more performance enhancement than spending an equal amount on a different speaker.  My congratulations to Phil Clements for using his expertise to design a great speaker line at reasonable cost.   Hopefully, it will become contagious."